How install wireless router

Step 9 Activate the wireless connection in the router configuration menu to enable the broadcast of wireless connection. If the broadcast is unsecured, the computer will automatically connect to the Wireless Network. How to Share a Printer on a Wireless Network.

How to Write a Bibliography for Internet Sources. How to Delete a Program from Computer Memory. How to Install Wireless Router. Select the equipment to be used. Unplug the DSL modem from the power supply. Connect the loose end of the Ethernet cable to the back of the router. Connect one end of the Ethernet cable that comes with the router package to one of the normally four available Ethernet ports at the back of the router.

Connect the router to the power source. Once the software is successfully installed, open your Web browser then enter the IP address Activate the wireless connection in the router configuration menu to enable the broadcast of wireless connection. How to Build a Computer from Scratch. If antennas are separate from the main router unit, you'll want to install them.

This is usually done by screwing them on to the connectors on the back or sides of the router. In other cases, the router's antennas will be built in, and only need to be extended and positioned.

Once it is unpacked and assembled, you'll need to find a place to install the router. The ideal router position will be in a central location, rather than at one end of the home. Since routers broadcast in all directions, you'll want to put it roughly in the middle of your home to get the best coverage and signal strength.

A higher position -- such as up on a shelf -- is preferred, since radio waves move out and down as they propagate through your home.

You'll also want to avoid potential interference from metal objects, brick or concrete walls. And stay away from the microwave, since it puts out the same frequencies that your wireless signal uses. Once it is powered on, you should see the router's indicator lights activate. Some will blink or change color during the setup process, indicating certain functions and changes, but there should be a light that shows when the router is properly plugged in and turned on.

Wait a minute or two after plugging in the router, as it may take a few moments for it to get up and running. For this, you'll use a basic Ethernet cable, plugged into the router's WAN or internet port. This port is usually distinguished from others on the device with a different color, or it may be physically separated from the rest of the ports with a space. Watch the router's LED indicators as you plug in the cable.

You should see a color change or a new light that indicates an active internet connection has been established. Not Helpful 10 Helpful Babawale Oladapo. For you to reset your admin password, you will need to reset your router to its default factory settings. Not Helpful 9 Helpful You can use Wi-Fi with a smartphone which is what most people have these days , not with a basic cell phone.

Not Helpful 5 Helpful You can remove Ethernet cables from devices that are going to be wireless e. Don't forget to configure the router first! Not Helpful 20 Helpful You have to do it from the device itself. On settings in any device, there should be a Wifi symbol and wireless networks available.

Not Helpful 17 Helpful Less than an hour, depending with your modem speed. It will also depend on how comfortable you are with setting it up, be sure to read the instructions closely. Not Helpful 0 Helpful 1. What can I do if I put in the correct username and password to connect to the router, but it doesn't work? The only thing you can do at that point is to restore your router to its default factory settings. Not Helpful 1 Helpful 0. I am out of LAN ports on my router and need one more. How can this be accomplished?

Add a 4-port or higher count network switch. You now have four new LAN ports; connect the original devices and you'll still have open ports. Using a switch lets you add more ports without needing configuration. Don't use a "hub" too slow or a router too complex. Make sure you use Cat5 cable for short jumps under 2m or Cat5e for runs under 10m.

Since 1Gb networks are common, be sure you use hardware that supports that speed. Not Helpful 0 Helpful 2. It's up to you, but most people do leave their routers on all the time. Not Helpful 1 Helpful 2. It's possible that it's overheating. Try to move it to a place with more ventilation.

If that does not work, then try a factory reset. If those suggestions fail, then your device is defective, and you will have to buy a new one. Not Helpful 0 Helpful 0. Include your email address to get a message when this question is answered. If you have procured a used wireless router from a friend or store, make sure to reset it to factory settings before installing it.

It may try to configure your wireless network according to the previous system. Find the reset button on the router, and press it for 30 seconds with a pin or pencil. Helpful 0 Not Helpful 0. You Might Also Like How to. How to. Expert Interview. About This Article. Co-authored by:. Co-authors: Updated: December 19, Categories: Featured Articles Wireless Networking. Article Summary X To set up a router in your home, connect the router to your wireless modem with an Ethernet cable, plug the router's power cable into a power source, and turn on the router if it doesn't start up already.

Italiano: Configurare un Router Wireless. Nederlands: Een draadloze router installeren. Bahasa Indonesia: Menyiapkan Router Nirkabel. Thanks to all authors for creating a page that has been read 1,, times. Rated this article:. More reader stories Hide reader stories. Is this article up to date? Cookies make wikiHow better. By continuing to use our site, you agree to our cookie policy.

Raphael Hoyles Oct 10, William Martinez Jul 10, I like the fact it is easy to follow and the images are large and easy to pick out.