Sbc6120 manual


















I could just insist on 75 signups and then just order 50 kits airlines do it every day - it's called "overbooking"! If we don't make the minimum of 50 paid orders by the close of orders then I'll just refund everybody's PayPal payment and we'll call the whole thing off.

A special order of white paddles would take at least 16 weeks to fill, and I've made the executive decision that we're not going to do that. The white does look a little better, I'll admit, but we've used black in the past and it looks pretty good with the FP colors.

LEAD TIME The gating item for me to ship the kits will be the faceplates Although they only take a few days to manufacture, we have to wait for our turn to come around in the vendor's queue, and that'll take six weeks.

Everything else switches, PCBs, LED bars, etc should be faster than that so when the faceplates come in I'll box 'em up and ship them to you. With this many orders it might take as much as two weeks for me to get everything packed up and shipped, so figure that the last kit should be shipped after about eight weeks.

Assuming that I start placing orders on or around February 5th, that would be April 2nd. It just takes way too much time and effort to keep track of what everybody wants and calculate special shipping charges when everybody wants something different.

My advice to the people who only want this part or that is to get together advertising on the Spare Time Gizmos Yahoo! Send an email directly to bob SpareTimeGizmos. I'll then send you a PayPal bill for the amount due, which you can then pay, and we'll get this thing going! If you have questions or think of something that I haven't mentioned, then please post them to the Spare Time Gizmos group.

Two things have happened since most of you quickly expressed your interest in purchasing these terrific kits: 1. All shipments to California addresses must also pay 9.

Gibson Firebird X Manuals. Gibson Musical Instrument G Service manual 25 pages. Gibson Other Instruction manual 2 pages. Gibson Other Installation instructions 2 pages. Gibson Other D Instruction manual 2 pages. Gibson Power Supply Manuals. Gibson Refrigerator Owner's manual 20 pages, 1. Gibson Frigidaire Manuals. Gibson Refrigerator Frigidaire Use and care manual 19 pages, 0.

Gibson Dark Fire Applications Manuals. Gibson Ventilation Hood Instruction manual 2 pages. Gibson Ventilation Hood Installation instructions 2 pages. Gibson GPS-1 Manuals. Gibson Washer Owner's manual 14 pages, 0. Gibson Washer A Use and care manual 11 pages, 0. Setting the HALT key down did that. Checked the parts collection against the Parts List. Printed a full size color photo of the completed board on glossy paper. Gathered and arranged the parts shown initially at right.

However, lots of other types of terminals would work. These are not on the parts list. Note that bypass caps are not labeled on the silkscreen. Note that the polarity for C29,30,31,21 are shown on the silk with tiny pluses. One is opposite from the others. IC sockets. I used foam as at right to insure they were seated during soldering.

Not stuffed until ready to mount on FP board. Set a lab power supply for 5VDC, current limited to mA. With the supply off, use insulated alligator clip leads to connect it the 4-pin power connector on the SBC. Positive goes to the pin closest to the corner of the board. Negative goes to the pin next to it. Run Tera Term or other terminal software on the PC. Press OK. On the menu bar, select Setup Serial Port.

Set Port to the COM port you are using. Check the baud rate, which should be if you placed the jumper across J Change Data to 7-bits. Leave Parity and Flow at none.

Note that if you wish to send a paper tape or other data file to the SBC later, you will need to change Data to 8-bits and may need to set Transmit Delay. Facing the four LEDs, only the one on the left power indicator and the one on the right should remain on.

The code indicates that the monitor software is running. It goes off, if you transfer control to a program in normal memory. Recall that the monitor code runs in its own memory. All rights reserved. PCB photo here. Carefully review the solder connections, looking for any solder bridges, splashes, bits of metal or unsoldered joints. Check the settings there. That will format and test partition 0 on the CF card takes a couple minutes. Windows will not understand the format and may ask if you want to format the card.

Decline that. However, NOTE which drive it has assigned to the card. Download InstallOS8.



0コメント

  • 1000 / 1000