This beep can be disabled or reconfigured to sound for different durations by using the following programming barcodes. Page Cradle Beep Loudness Control The beep loudness of cradle can be defined with the following levels. ON for Fail msec Data trans.
Fold out the back cover of this manual. You will see a table of alphanumeric barcodes, which are used to program the various options presented. In most of the cases, simply selecting an appropriate cable with a device code will work for a specific interface.
Interface selection: You can change factory interface default for other type interface. The installation of the wedge is a fairly simple process without any changes of software or hardware. Keyboard Type: Select keyboard type connector of your host computer. Page 38 Keyboard wedge Keyboard Layout: The selecting of keyboard layout supports many country languages other than USA keyboard layout. First you need to confirm country language that you desire.
Power-on simulation: All of the PCs check the keyboard status during power-on selftest. It is recommended to Enable function if you are working without keyboard installation. It simulates keyboard timing and pass keyboard present status to the PC during power-on.
The light source of imager stops scanning when there is a successful reading or no code is decoded after the Stand-by duration elapsed.
Momentary-The trigger button acts as a switch. Press button to activate scanning and release button to stop scanning. Page 50 Scan Global min. Code length less than min. In popular, you can set the same value for both min. Page Indication Indication Exit Power on alert: After power-on the cradle it will generate an alert signal to indicate a successful self-test.
LED indication: After each successful reading, the LED above the imager will light up to indicate a good barcode reading. Beeper indication: After each successful reading, the imager will beep buzzer to indicate a good barcode reading, and its Beep loudness, Check-sum transmission: By setting Enable, checks sum will be transmitted. By setting one or two digits to indicate which insertion group you want to insert. You may refer to Character insertion. The function is to insert specific characters as a group into transmitted data of selected symbologies.
Page Transmission Transmission Preamble transmission: By setting Enable, Preamble will be appended before the data transmitted. Postamble transmission: By setting Enable, Postamble will be appended after the data is transmitted. Insert data group position: The scanner offers 4 positions to insert among the symbol.
Page 26 no insertion Insert data group 1 position no insertion Insert data group 2 position no insertion Insert data group 3 position no insertion Insert data group 4 position Before code data After code data Code ID position Page Scan Scan Scanning mode: Good-read off-The trigger button must be pressed to activate scanning.
The light source of scanner stops scanning when there is a successful reading or no code is decoded after the Stand-by duration elapsed. Momentary-The trigger button acts as a switch. Press button to activate scanning and release button to stop scanning. Page 30 Good-read off Momentary Scanning mode Alternate Timeout off Continue Test only second Stand-by duration 10 msec Double read timeout no double Double confirm confirm Supplement Check Counter Exit Page 31 Scan Global min.
The length is defined as the actual barcode data length to be sent. Label with length exceeds these limits will be rejected. Make sure that the Minimum length setting is no greater than the Maximum length setting, or otherwise the labels of the symbology will not be readable.
It will beep instead of reading anything when the truncate value is more than the barcode data digits or the value of Truncate Leading is overlapped with that of Check-sum transmission: By setting Enable, checks sum will be transmitted.
Page 46 Truncate ending Exit Check-sum transmission: By setting Enable, checksum will be transmitted. Page 58 Disable Enable Check-sum transmission Max. Checksum Transmission: By setting Enable, checksum will be transmitted. Page 67 Code Max. Characters defined arrgox prefix or suffix characters will be transmitted immediately with the scanned data for all symbologies. This beep can be disabled or reconfigured to sound for different durations by using the following programming barcodes.
System Control Scan Scanning mode: The light source of scanner stops scanning Fasten the screw to the imager. Fold out the back cover of this manual. Keyboard wedge Caps Lock: By setting Enable, checksum1 and checksum2 will be transmitted upon your selected checksum verification method. After power-on the cradle it will generate an alert signal to indicate a successful self-test. The checksum is made as the sum module of all data digits. Default setting For each mankal shown as below:.
This website uses cookies to improve your experience while you navigate through the website. Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are as essential for the working of basic functionalities of the website.
We also use third-party cookies that help us analyze and understand how you use this website. Program Option Bar Code Option characters Insert G1 characters setting characters Insert G2 characters setting characters Insert G3 characters setting characters Insert G4 characters setting The checksum argxo presented as the sum module 11 of all data digits. Page 2 The ArgoxScan can automatically scan barcode at a distance. Store battery pack in a proper place. They are appended to the data automatically when each barcode is decoded.
Loosen sa screw at the bottom of the imager. When the imager and cradle are linked together, the imager will read and decode barcodes and transmit them via a Wireless radio to the cradle. The checksum is presented as the sum module 10 or 11 of the data digits. Page 71 Codabar Insertion group number selection: Default setting For each barcode shown as below: Indication Indication Exit Power on alert: The checksum of Code The checksum is made as the sum module 10 of manuao numerical values of all data digits.
The scan line must cross the entire barcode.
0コメント